Free Download Cyclic Oxidation of High Temperature Materials – Proceedings of an EFC Workshop, Frankfurt/Main, 1999 By by Schütze, M.; Quadakkers, W. J. (Eds.)
1999 | 489 Pages | ISBN: 1861251009 | PDF | 27 MB
Proceedings of a workshop organised by the European Federation of Corrosion, Frankfurt/Main, 1999, the papers review the current understanding of materials behaviour under cyclic oxidation. Content: Front Matter Series Introduction Preface Foreword Table of Contents Part I. Oxidation and Failure Mechanisms Under Cyclic Conditions 1. Interfacial Crack Growth During Temperature Changes 2. The Influence of Surface Pre-Treatment on the Integrity of Alumina Scales on the ODS Alloy MA 956 3. The Effect of Water Vapour on the Oxidation of Alloys That Develop Alumina Scales for Protection 4. The Influence of Thermal Cycling on Internal Oxidation and Nitridation of Nickel-Base Alloys 5. Cyclic Oxidation of Thin FeCrAl(RE) Foils in Air: SEM and EPMA Investigations 6. Cyclic Oxidation of PM 1000 Part II. Test Procedures and Parameters Influencing Cyclic Oxidation Behaviour 7. Effect of Cycle Frequency on High-Temperature Oxidation Behaviour of Alumina- and Chromia-Forming Alloys 8. The Effect of Thermal Cycling on the Mechanical Failure of Alumina Scales Formed on Commercial FeCrAl-RE Alloys 9. Cyclic Oxidation Testing and Modelling: A NASA Lewis Perspective 10. Significance of Experimental Procedures on the Hot Corrosion Behaviour of Nickel-Base Alloys Under Cyclic Conditions 11. Advantages of Ferritic Stainless Steels in Cyclic High Temperature Conditions 12. Investigation of a New Methodology in High Temperature Oxidation 13. Effect of Implanted Silicon on the Cyclic Oxidation Behaviour of AISI 304 and AISI 430 Stainless Steels 14. The Importance of Relevant Experimental Parameters for High Temperature Cyclic Oxidation Experiments 15. Corrosion of Heat Exchanger Steels in Cycled Gas Atmospheres at 600°C 16. Behaviour of Protective Coatings Against Sulfidation Under Cyclic Conditions Part III. Long Term Behaviour and Near-Service Conditions 17. Long-Term, Cyclic Oxidation Behaviour of Three Chromia-Forming Alloys Exposed to Air at 982°C 18. Oxidation Limited Life of FeCrAl Based Alloys During Thermal Cycling 19. Characterisation of Oxidation Resistance of Heat-Resistant Cast Alloys in the 5 x 24-h Test 20. Cyclic Oxidation Testing by Resistance Heating Part IV. The Behaviour of Coatings Under Cycling Conditions 21. Thermal Cycling Testing of Thermal Barrier Coatings 22. Investigations of the Microstructure and Stress State in Oxide Scales and Buried Layers with Diffraction Methods 23. Numerically Calculated Oxidation Induced Stresses in Thermal Barrier Coatings on Cylindrical Substrates 24. Electron Beam-Physical Vapour Deposited Thermal Barrier Coating Lifetime Response to Various Bond Coat Pre-Treatments 25. Degradation of Aluminide, Chromium-Aluminide and Thermal Barrier Coatings in Conditions of Cyclic Thermal and Mechanical Loads 26. Thermal Cycling of NiAl Intermetallic Coatings Prepared by High Velocity Oxy-Fuel (HVOF) Thermal Spraying 27. Development of Metal-Organic Chemical Vapour Deposition (MOCVD) Coatings for Protection of Alloys Under High Temperature Cyclic Conditions 28. Mullite Based Oxidation Protection for Silicon Carbide-Carbon/Carbon Composites in Air at Temperatures up to 1900K 29. Cyclic Oxidation – Guidelines for Test Standardisation, Aimed at the Assessment of Service Behaviour List of Abbreviations Index